www.gflames.fora.pl

nukk41df

A Beginners Guide to the Application of Computer-Cut Vinyl LetteringArticle Summary: A beginners guide to [url=http://www.riad-marrakesh.fr]www.riad-marrakesh.fr[/url] the application of computer-cut vinyl lettering
References:
About the Author:
Matthew Theobald Article Feed : [url=http://www.hayasoft.com/lock/maho/bbs2/light.cgi?res=1241]abercrombie pas cher Choose T[/url]
Pen-marking method
Using a standard ballpoint pen mark a line on the substrate corresponding to the baseline of the text to be applied. Mark the line as lightly as possible - consider using a series of dots or short [url=http://www.montresidole.fr]doudoune moncler[/url] lines which will be less visible if there are issues when removing the line. When the vinyl is to be applied to perspex or paintwork, try to use a marking colour that is similar to the substrate colour; some types of paintwork can be stained by chinagraph or ink so it would make sense to test [url=http://www.lotogame.fr/hollisterfrance.php]hollister pas cher[/url] it first in a discreet area.
Remove the text or logo from the release paper liner and hold firmly at each end. Line up the baseline of the text with the line marked on [url=http://www.footdedemain.fr]jordan pas cher[/url] the substrate while keeping the text just away from the surface - you should be able to see the line through the application tape.
Lightly press the extremities to the surface [url=http://www.milimania.com/portal/e107_plugins/forum/forum_viewtopic.php?56342.last]louboutin pas cher ECO FRIENDLY HP TONER - written by Emiley[/url] to secure the text or logo in place. Next, using a vinyl applicator and starting from the centre of the graphic, press outward from the centre, up and down, working your way towards one end. Repeat the process working towards the other end.
Lift a corner of the application tape and peel back while keeping it as flat to the surface as possible; doing this helps to prevent the vinyl being pulled off of the substrate and also stops any paint being removed when the application is onto a painted surface.
Depending on what you have used to create the line it can be removed using meths, lighter fuel or alcohol spirit - make sure to test that it will not damage the substrate.
Hinge Method
Fold graphic in half and press a small fold into the bottom of the graphic. Place a piece of masking [url=http://www.paolofranco.it/hogan-outlet/]hogan outlet[/url] tape at each end of the graphic and secure to the substrate. Adjust the positioning until the fold mark in the application tape corresponds with the measured centre point of the substrate.
Again, using a retractable tape measure lift one end of the graphic and move up or down until it is in the required position. Do the same to the other end and then re-check the first end as [url=http://www.cod-esports.fr]abercrombie pas cher[/url] it will probly have moved.
Once the text or logo has been positioned [url=http://www.chu-forex.fr/airjordan.php]nike air jordan pas cher[/url] apply a strip of masking tape at right angles to the length of the graphic - ideally with one edge falling between letters so that the graphic can be folded along that line without creasing the vinyl itself. This is known as the hinge.
Take a small piece of tape and apply to the substrate so that it butts up against the bottom of the application tape at the opposite end [url=http://www.sandvikfw.net/shopuk.php]hollister sale[/url] from the hinge. Remove the piece of tape, at that end, securing the graphic to the substrate and fold back the grahpic 180 [url=http://www.168huafei.com/viewthread.php?tid=27010&extra=]hogan outlet How do I apply for a Fiance Visa - written by Rachel Immig[/url] degrees and press a sharp fold into it.
Peel back the release paper and [url=http://www.paolofranco.it/scarpe-hogan/]scarpe hogan[/url] tear it off at the fold line. Bring down the application tape towards the surface of the substrate while keeping it taught and line up the edge of the masking tape with the edge of the application tape. Next, using a vinyl applicator and starting from the centre of the graphic, press outward from the centre, up and down, working your way towards one end. [url=http://www.jeremyparendt.com/Barbour-Paris.php]barbour pas cher soldes[/url] Repeat the process working towards the other end.
Lift a corner of the application tape and peel back while keeping it as flat to [url=http://www.piktor.fr/doudoune-moncler/]doudoune moncler[/url] the surface as possible; doing this helps to prevent the vinyl being pulled off of the substrate and also stops any paint being removed when the application is onto a painted surface. This method has the advantage of not needing any lines to mark the position and is therefore useful for applications to sensitive surfaces.
Where the graphic does not allow for a centre hinge, because of the lack of a suitable gap in which to create the fold, the hinge can be created at one end [url=http://www.lotogame.fr/hollisterfrance.php]hollister france[/url] of the graphic or along the top or bottom.
Article Source: uPublish.info
**NOTE** - has claimed original rights on [url=http://www.piktor.fr/air-jordan-pas-cher/]air jordan pas cher[/url] the article "A Beginners Guide to the Application of Computer-Cut Vinyl Lettering" ... if there is a dispute on the originality of this article ... please contact us via our and supply our staff with the appropriate details of dispute (ie ).
Matt has been involved in the design and production of exhibition stands for 2 decades and has run his large-format digital printing business [url=http://www.piktor.fr/abercrombie-pas-cher/]abercrombie pas cher[/url] in Maidenhead for the last [url=http://www.footdedemain.fr]jordan[/url] 8 years.
Keywords: , , ,
Category:
(c)